Wavetek 39A Dokumentacja Strona 25
- Strona / 137
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
User Manual 301/302
Grounding
Requirements
To ensure the safety of operating personnel, the U.S. O.S.H.A.
(Occupational Safety and Health) requirement and good engineering
practice mandate that the instrument panel and enclosure be "earth"
grounded. The long offset pin on the male end of the power cable
carries the ground wire to the long pin of the Euro connector (DIN
standard) receptacle on the rear panel of the instrument.
To preserve the safety protection feature when operating the
instrument from a two-contact outlet, use a three-prong to two-prong
adapter and connect the green lead on the adapter to an "earth"
ground.
WARNING
Do not attempt to float the output from ground as it may damage
the Model 301/302 and your equipment.
CAUTION
To avoid operator shock hazard do not exceed the power mains
voltage frequency rating which limits the leakage current
between case and power mains. Never expose the instrument to
rain, excessive moisture, or condensation.
Long Term
Storage or
Repackaging For
Shipment
If the instrument is to be stored for a long period of time or shipped
immediately, proceed as directed below. If you have any questions,
contact your local Wavetek-Datron Representative or the Wavetek-
Datron Customer Service Department.
1. Repack the instrument using the wrappings, packing material
and accessories originally shipped with the unit. If the original
container is not available, purchase replacement materials.
2. Be sure the carton is well sealed with strong tape or metal
straps.
3.
Mark the carton with the model and serial number. If it is to be
shipped, show sending and return address on two sides of the
box.
NOTE
If the instrument is to be shipped to Wavetek-Datron for
calibration or repair, attach a tag to the instrument identifying
the owner. Note the problem, symptoms, and service or repair
Configuring The Instrument
14
- WARRANTY 3
- Exclusion of Other Warranties 3
- DECLARATION OF CONFORMITY 4
- Model 301 and Model 302 4
- SAFETY PRECAUTIONS 5
- Table of Contents 6
- 301/302 User Manual 10
- Table of Figures 10
- Getting Started 12
- Introduction 13
- Input and Output 16
- Connectors 16
- Operating Modes 17
- Continuous Mode 18
- Triggered Mode 18
- Burst Mode 18
- Gated Mode 18
- Output Type 18
- Standard (Fixed) 19
- Waveforms 19
- Arbitrary (User) 19
- Sequenced 20
- Output State 22
- Front Panel 22
- Indicators 22
- Programming The 22
- Model 301/302 22
- CONFIGURING The INSTRUMENT 23
- Performance 24
- Requirements 24
- Preparation For 26
- Logical Address 26
- Selection 26
- Installation 27
- Bench Operation 27
- Rack Mounting 27
- USING The INSTRUMENT 28
- Power On/Reset 29
- Defaults 29
- Programming the 29
- :VOLTage 2; 30
- ÷ 2) ≤ 5 30
- Controlling the 31
- 301/2 Using 31
- WaveWiz 31
- Controlling 33
- Instrument 33
- Functions 33
- Using the APPLy 33
- Selecting the 36
- Active Channel 36
- Enabling the Main 37
- Selecting an 38
- Selecting a 39
- Standard 39
- Function Shape 39
- Changing the 42
- Frequency and 42
- Sample Clock 42
- External SCLK 43
- Output Amplitude 44
- Filter Type 45
- Operating Mode 46
- Selecting the Trigger 49
- Using the Internal 50
- Trigger Generator 50
- Assigning the 52
- Source For The 52
- SYNC Output 52
- Generating 53
- Arbitrary 53
- What Are 54
- Waveforms? 54
- Arbitrary Memory 55
- Management 55
- Loading Arbitrary 56
- Reversing Byte 58
- Using WaveWiz to 59
- Generate 59
- Using Equation 62
- Editor to Generate 62
- User Manual 301/302 68
- Configuring the Instrument 68
- Fast Binary 72
- Sequence Table 72
- Download 72
- Selecting active 74
- Sequence 74
- Running 75
- Sequences 75
- Using WaveWiz 75
- Advance 77
- Advance Source 78
- Sequences with 79
- Sequences with 80
- Adjusting Phase 84
- Offset Between 84
- Channels 84
- Amplitude 86
- Modulation 86
- System-Related 86
- SCPI Commands 87
- SCPI COMMAND REFERENCE 89
- Query Response 90
- SCPI Command Reference 91
- Subsystem 106
- INSTrument 110
- Trigger 111
- IEEE-STD-488.2 119
- Commands and 119
- Registers 120
- The SCPI Status 120
- The Status Byte 121
- Register (STB) 121
- Generation 122
- Standard Event 124
- Status Register 124
- Status Enable 125
- Register (ESE) 125
- Error Messages 125
- Device-Specific 128
- Commands 128
- Appendix A SPECIFICATIONS 130
- Triangle 131
- Pulse/Ramp 131
- ARBITRARY WAVEFORMS 132
- SEQUENCED SEQUENCES 133
- OUTPUTS (CHANNELS A & B) 134
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.061 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji